AMTEC adalah produk OLI INDUSTRI (USA), terbukti mengefisiensikan produktifitas hingga 200%.
Klaim dari Pabrik AMTEC USA.
AUTOMOTIVE LUBRICANTS
Product Data Sheet
AMTEC GOLD XP ENGINE OIL
AMTEC GOLD XP ENGINE OIL is a premium long drain diesel and gasoline engine oil protects your engine from the serious damaging effects of high stress the engine. It meets the requirements for super-high performance all season diesel and gasoline engines in severe service and under varying operating conditions.
AMTEC GOLD XP ENGINE OIL is manufactured with a combination of the highest quality synthetic blend and petroleum base stocks and special scientifically selected additives. This blend protects against the formation of sludge and engine lacquer because of its high detergency-dispersions. It contains exceptional anti-wear additives which protect metal surfaces against wear and scuffing caused by heavy loads and boundary lubrications conditions. It provides high TBN protection against the formation of acids.
The performance AMTEC GOLD XP ENGINE OIL provides the following extra benefits not found in conventional diesel and gasoline engine oils:
- It has much better long drain capability. Service in diesel land gasoline engine can be extended up to twice the builder recommended drain engine.
- It has better multipurpose use to both gasoline and diesel engine.
- It has extra high viscosity index for greater protections at low temperatures and high temperature.
- It has extra high detergent level has extra protection against the formation of corrosive acids It has lower oil consumption, provides a better protective film in the high-temperature ring area.
- It has better heat and oxidation resistance, above conventional ordinary oils.
- Protects better against oil thickening, varnish and lacquer.
- It will result in reduced maintenance and downtime where when used in place of conventional ordinary oils it will lengthen the life of the engine.
TYPICAL SPECIFICATIONS bbbbbbbbbbbbb
TABLE
| No. SAE | 15W40 |
| API Service | CF-4/SJ |
| Mass Density | at 15/4 oC 0,884 |
| Viscosity | at 100 oC, cSt 14,5 |
| Viscosity Index | 135 |
| Flash Point | 15W40 |
| Total base Number (TBN) Mg KOH/gr | 14 |
Approvals
AMTEC GOLD XP ENGINE OIL is a high performance motor engine oil meating following specifications:
- API CF-4 / SJ
- CCMC-D41G4/PD-2
- MIL-L-46152E
- MIL-L-2104E
- Mack EO-K/2
- Allison C-4
The name of this product or group of product is for product identification only. HUSK-ITT CORPORATION makes no warranties, representation or conditions of any kind expressed implied, whether for merchantability of fitness with respect to these products.
AUTOMOTIVE LUBRICANTS
Product Data Sheet
AMTEC SILVER XP ENGINE OIL
AMTEC SILVER XD ENGINE OIL is a premium quality crank case oil designed for all-weather operation of passenger cars and light duty trucks. Extra Heavy Duty Motor Oil provides excellent protection against deposits resulting from high temperature operation. It also provides excellent protection against sludge deposits resulting from the severe service of short trip, stop-and-go driving.
AMTEC SILVER XD ENGINE OIL is blend of the highest quality base oils and selected additives. The anti-wear additive in Extra Heavy Duty Motor Oil minimizes wear and scuffing of metal surfaces under boundary lubrication conditions. The detergent-dispersant additives protect against sludge formation and varnish deposits. The anti-oxidation during the high underhood temperatures encountered in modern driving. Selected alkaline additives protect against the formation of acid components. Rust and corrosion additives protect metal parts during engine operation and shut down. Extra Heavy Duty Motor Oil contains an anti-foam agent. It has excellent low temperature performance.
FIELD SERVICE APPLICATION
It meets the equipments for gasoline and diesel engines in present and earlier passenger cars, vans and light truck operating under vehicle manufacturers recommended maintenance procedures. Engine oils developed for this category provide performance exceeding the minimum requirements of API Service Category CF/SF, which it is intended to replace, in the areas of deposit control, oil oxidation wear, rust and corrosion.
TYPICAL SPECIFICATIONS ccccccccccccc
| No. SAE | 40 |
| API Service | CF/SF |
| Mass Density | 15/4 oC 0,895 |
| Viscosity | at 100 oC, cSt 14,5 |
| Viscosity Index | 100 oC, cSt 14,7 40 oC, cSt 144 |
| Flash Point | 240 |
| Total base Number (TBN) Mg KOH/gr | 12 |
BENEFIT
- Help extend engine life
- Recommend for turbo-charged diesel engine
- Minimizes piston and combustion chamber deposites
- Specially formulated for off highway heavy duty diesel equipment
- Contains anti wear and anti scuff agents
The name of this product or group of product is for product identification only. HUSK-ITT CORPORATION makes no warranties, representation or conditions of any kind expressed implied, whether for merchantability of fitness with respect to these products.
AUTOMOTIVE LUBRICANTS
Product Data Sheet
AMTEC ATF DEX - 3
AMTEC ATF DEX – 3 is new generation petroleum based fluid for automatic and power shift transmissions. It fully qualified both as a dextrin III and Mercon lubricant surpassing 6297-M and Ford specification M2C185A. in addition AMTEC ATF DEX – 3 is an approved Allison C-4 fluid and a Caterpillar TO-2 lubricant.
The key features of AMTEC ATF DEX – 3 are its low ash (non zinc) technology and stable anti-wear system. The benefits of these are excellent compatibility yellow metals and much improved friction durability due to the reduced binding of the traction surfaces from ash deposits.
AMTEC ATF DEX – 3 is recommended for mobile equipment used by utility companies, which require electrical insulating properties for hydraulic oils. AMTEC ATF DEX – 3 provides superior wear protection for all passenger car and light trucks reguiring the use of a Type A, Dexron 11, Dexron 11 E or Dexron III ATFs. This product is recommended for use in GMC, Ford, Chrysler, Volkswagen, Nissan, Toyota, Honda, Audi, Renault, Porsche, Mercedes Benz and many other vehicles.
TYPICAL SPECIFICATIONS
PROPERTIES METHOD RESULTS
Density @ 15oC, kg/I ASTM D-4052 0.872
Flash Point, oC ASTM D-92 196
Pour Point, oC ASTM D-97 -42
Kinematic Viscosity, cST ASTM D_445
@ 40oC 33.50
@ 100oC 7.41
Viscosity Index ASTM D-2270 197
Appearance Visual Red
Benefit
- Excellent thermal stability
- Resistance to high temperature oxidation and fluid thickening
- Excellent low temperature characteristics even at temperature below -40 oC
- Its friction-modifying properties ensure consistent, smooth shifts in all driving conditions
- The anti-wear and frictional properties of these fluids also allow it to satisfy the needs of certain hydraulic requirements
- Stop and prevent automatic and power shifts transmission seal leak
Approvals
AMTEC ATF DEX – 3 has gained approvals against the following specifications:
- General Motors Dextron-III
- Ford Mercon
- Allison C-4
It can be used in off-highway transmission, power steering and other hydraulic systems for which a Dextron III or Allison C-4 fluid is specified.
The name of this product or group of product is for product identification only. HUSK-ITT CORPORATION makes no warranties, representation or conditions of any kind expressed implied, whether for merchantability of fitness with respect to these products.
AUTOMOTIVE LUBRICANTS
Product Data Sheet
AMTEC GEARTEC MP
AMTEC GEARTEC MP are all-purpose, extreme pressure gear oils formulated from the highest quality selected base oils and Additives available. AMTEC GEARTEC MP have been compounded to be more reliable, even under the toughest conditions. These high-quality oils have been formulated to give extra protections in high-temperature applications. Special Polymers additives track on all gear teeth, coating the metal surface to reduce backlash and quiet worn or noisy gears.
ADHESIVE – COHESIVE QUALITIES
Specials additives improves the adhesion of AMTEC GEARTEC MP to metal surfaces and the special extreme pressure additives prevent wear.
AMTEC GEARTEC MP outstanding quality the versatility of their applications, which include almost all worm, spur, herringbone, and planetary gears. They are designed primarily for industrial gear applications but are excellent for automotive uses such as manual transmissions.
ADVANTAGES
- Suited to different applications
- Excellent load-carrying capacity
- Reduces wear and protects against scuffing
- Protect against rust, corrosion and foaming
- Helps Quiet worn and noisy gears
- Meets API GL-4, GL-5 and GL-6 requirements
TYPICAL SPECIFICATIONS
AMTEC GEARTEC MP 90 GEAR OIL 140 GEAR OIL 85W-140 GEAR OIL
Viscosity SUS @ 100 oF 1100 2430 2200
Viscosity SUS @ 210 oF 90 138 134
Viscosity Index, min, 92 9.3 94
Gravity, API 22.4 21.3 33.6
Flash Point, oF 470 518 500
Pour Point, oF 0 -3 -4
Rust Test ASTM-D-665 (Poc.A.) PASS PASS PASS
Timken OK load, lbs. 60 60 60
Oxidation Tes ASTM-D-943 PASS PASS PASS
SAE Viscosity Grade 90 140 85-140
Colour BROWN BROWN BROWN
The name of this product or group of product is for product identification only. HUSK-ITT CORPORATION makes no warranties, representation or conditions of any kind expressed implied, whether for merchantability of fitness with respect to these products.
AUTOMOTIVE LUBRICANTS
Product Data Sheet
AMTEC INDUSTRIAL GEAR LUBE
AMTEC INDUSTRIAL GEAR LUBE comprise a family of extreme-pressure gear lubricants designed to operate over a very wide range of temperature and conditions. These fluids possess excellent high temperature oxidation stability and superior low temperature fluidity.
The incorporation of special additives in AMTEC INDUSTRIAL GEAR LUBE protects equipment from rust, corrosion and foaming, In addition, extreme pressure additive provide optimum protection against shock loading and offer high load carrying capabilities. As the gears work hard and get hot, special phosphorous and sulphur compound in AMTEC INDUSTRIAL GEAR LUBE combine with the metal, producing a lubricating film between the surfaces of the meshing gear teeth. The thickness of this film varies according to prevailing conditions, giving the ring amount of protection from scuffing thus ensuring long component life span.
AMTEC INDUSTRIAL GEAR LUBE find applications in virtually all types of industrial settings, Some typical application include gear sets and oil circulating systems in steel mills, foundries, glass and bottle manufacturing plants, injection molding machines, paper mills, electric wheel motors used in surface mining and quarries, shearing arms used in underground coal mining, cement klins, petroleum and chemical processing plants.
TYPICAL SPECIFICATIONS
PROPERTIES METHOD RESULTS
ISO Viscosity Grade 68 100 150 220 320 460 680
Density @ 15oC, kg/I ASTM D-4052 0.882 0.886 0.894 0.898 0.903 0.907 0.912
Flash Point, oC ASTM D-92 222 232 240 240 250 258 268
Pour Point, oC ASTM D-97 -18 -15 -12 -12 -9 -9 -6
Kinematic Viscosity, cST ASTM D-445
@ 40oC68 67.2 97 151 151 309 463 632
@ 100oC 8.50 10.90 14.7 14.7 23.6 30.5 32.5
Viscosity Index ASTM D-2270 100 100 100 100 100 98 82
Benefit
- Excellent low and high temperature performance
- Prevents rust and corrosion
- Reduces galling, scuffing and welding of gear teeth
Approvals
- USX 224, David Brown SI. 53.101 (E)
- AGMA 9005-D94
- DIN 51517 Part 3
AMTEC INDUSTRIAL GEAR LUBE have been used in the following application:
- Steel gear transmissions
- Industrial gear drive where a full performance is required
- Bearings
- Circulating and splash lubricated systems
The name of this product or group of product is for product identification only. HUSK-ITT CORPORATION makes no warranties, representation or conditions of any kind expressed implied, whether for merchantability of fitness with respect to these products.
AUTOMOTIVE LUBRICANTS
Product Data Sheet
AMTEC MACHINERY SPINDLE OIL
AMTEC MACHINERY SPINDLE OIL are premium quality, high performance oils that are designed to meet the severe demands for high speed spindle lubrication on textile spinning frames that are often running at speeds from 20,000 to 40,000 RPM. The AMTEC MACHINERY SPINDLE OIL are also highly recommended for machine tools where operating speeds are in excess of 10,000 RPM.
AMTEC MACHINERY SPINDLE OIL are formulated from premium quality base oils and compounded with the finest anti-corrosion, anti-foam, and oxidation inhibitor additives available. AMTEC MACHINERY SPINDLE OIL also contain a unique extreme pressure additive that provides greater wear protection than any other spindle oil in the market place. The low oil viscosity, coupled with the special extreme pressure additive, reduces friction, which lowers operating temperatures and improves machinery efficiency.
ADVANTAGES:
- ANTI-WEAR and CORROSION PROTECTION
- EXTREME PRESSURE PROTECTION
- NON-FOAMING
- SEPARATES-READILY FROM WATER
- MINIMIZES FRICTION, WEAR AND FOG
- WILL NOT THICKEN AND GUM
TYPICAL SPECIFICATIONS
TEST ASTM ISO ISO ISO ISO
METHOD 10 15 22 32
Color Amber Amber Amber Amber
Viscosity cSt @ 40oC D-445 10.0 18.1 21.5 30.0
Viscosity cSt @ 100oC D-445 2.27 3.25 3.36 4.10
Flash Point, oF D-62 269 280 315 365
Pour Point, oF D-665B -12.5 -15 -35.5 -41.0
Corrosion Preventative Test D-1401 Pass Pass Pass Pass
Emulsion E.P. Test D-3233B 5 5 5 5
Falex E.P. Test,
Pass load, ft. lbs 1000 1500 2000 2500
The name of this product or group of product is for product identification only. HUSK-ITT CORPORATION makes no warranties, representation or conditions of any kind expressed implied, whether for merchantability of fitness with respect to these products.
==========================================================
halaman 7
AMTEC SYNTHETIC SOLUBLE CUTTING OIL is a water soluble metalworking fluid that forms a very stable emulsion when mixed with water at a wide range of dilutions. The stability of this emulsion is not affected by hard water ions and the fact that it does not foam makes it ideal for high speed metalworking operations. The high heat absorbing characteristics of AMTEC SYNTHETIC SOLUBLE CUTTING OIL provides superior cooling for a variety of metalworking processes.
AMTEC SYNTHETIC SOLUBLE CUTTING OIL is fortified with biocides to prevent rancidity caused by bacteria, which can lead to unpleasant odours, split emulsion and reduced product performance. This feature results in greater worker satisfaction and optimum product performance. It also provides excellent protection against rust.
AMTEC SYNTHETIC SOLUBLE CUTTING OIL is recommended for light to moderate duty machining operation on all ferrous and non-ferrous metal except magnesium, it is used in machining, sawing, drilling, milling and turning. It is ideal for grinding due to its superior wetting and cooling properties. Typical dilution rations with water can range from 1 : 10 for milling and turning to 1 : 40 for grinding.
TYPICAL SPECIFICATIONS
PROPERTIES METHOD RESULTS
Density @ 15oC, kg/I ASTM D-4052 0.886
Flash Point, oC ASTM D-92 170
Kinematic Viscosity, cST ASTM D-445
@ 40oC68 36
@ 100oC 7.4
Appearance Visual Amber Fluid
Emulation Type Visual Dense White
Benefit
- Emulsify readily with water
- Non-foaming
- Protect against rust and corrosion
- Excellent wetting and cooling capabilities
- Resists bacterial attack
- Excellent lubricants
Applications
AMTEC SYNTHETIC SOLUBLE CUTTING OIL is used for general cutting operations in which maximum tool an workpiece cooling is required, and the emulsion must have some lubricating ability. The oil should be added grandualy into the full volume of water-not the reverse, and gentle agitation maintained until all the oil has been added and a uniform emulsion is obtained. The ratio of oil to water required to form an amulsified soluble oil varies with the metal being machined and with the machining techniques being used. The following ratio are suggested.
The name of this product or group of product is for product identification only. HUSK-ITT CORPORATION makes no warranties, representation or conditions of any kind expressed implied, whether for merchantability of fitness with respect to these products.
AMTEC S-800 SERIES SYNTHETIC OIL are formulated from a unique combination of the highest quality pure synthetic base oils then coupled with the latest technology in additives available to assure maximum wear, oxidation and corrosion protection, AMTEC S-800 SERIES SYNTHETIC OIL are designed to allow compressors to operate at optimum efficiency while eliminating varnish, sludge and carbon deposits thus extending both equipment ant lubricant life.
AMTEC S-800 SERIES SYNTHETIC OIL were primarily designed for all types of air compressors where a HIGH PERFORMANCE OIL is required. These versatile oils are offered in several viscosity grades to meet the different need of rotary vane, screw type and reciprocating compressors. Because of their excellent anti-wear, anti foaming and wide temperature characteristics, they exhibit outstanding performance when used as turbine oils, hydraulic oil, gear oils, and chain oils.
ADVANTAGES
Reduces friction and wear
Oxidation and Corrosion Protection
Reduces System Deposits
High Separation Efficiency
Extends Equipment and lubricants life
NOTE : AMTEC S-800 SERIES SYNTHETIC OIL are compatible with petroleum lubricants : However blending with other fluids will reduce their high performance characteristics. Conversion procedures from petroleum products are available on request.
TYPICAL SPECIFICATIONS
S-810 S-815 S-820 S-830
Density, lbs/gal., 60 oF 7.66 7.75 7.88 7.48
Viscosity SUS@ 40oC 44 49 52 59
Viscosity SUS @ 100oC 144 215 320 496
Flash Point, oF. 480 480 480 500
Pour Point, oF -60 -55 -35 -30
Fire Point, oF 530 425 480 550
Auto-ignition 730 750 760 800
Conradson Carbon % 0.02 0.02 0.02 0.02
Four ball Wear Test 0.49 0.43 0.45 0.47
(40 kg. 167 F 1200 RPM, 1 Hr)
SAE Grade, Weight 10 15 20 30
ISO Viscosity Grade
Viscosity Index 32
104 46
102 68
100 100
100
Approvals
For used rotary vane and screw type air compressors (oil flooded or oil injected, male or female, single or two-stage configurations). Also meet centrain high performance turbine quality and hydraulic oils:
- DIN 5 1506
- DIN 5 1524 Part II
- Cincinnati-Milacron P-68, P69, and P-70
- Denison HF-2, HF-0
- Vickers 1-286-S3
- Vickers M-2950-S
- U.S. Steel 126, 127
- AFNOR NFE 48-603 (HM)
The name of this product or group of product is for product identification only. HUSK-ITT CORPORATION makes no warranties, representation or conditions of any kind expressed implied, whether for merchantability of fitness with respect to these products.
AMTEC N-500 SERIES SYNTHETIC OILS are a blend of highest quality selected paraffinic base oils coupled with the finest rust and oxidation resistant additives available. This unique combination produces an exceptional lubricating oil with excellent thermal stability and low carbon forming characteristics. Formulated with only high-viscosity index oils to minimize viscosity changes during high and low temperature variations. Compounded to meet service requirements of Denison HF-2 and Cincinnati Millicrons high temperature heat stability test.
USAGE
AMTEC N-500 SERIES SYNTHETIC OILS were designed primarily for all types of Air Compressors requiring non-detergent oils. These versatile oils are offered in several viscosity grade to meet the different needs of reciprocating, centrifugal and rotary compressors. Because of their anti-wear, anti-foam and excellent stability characteristics, the show outstanding performance when used as turbine oils, drip oils, hydraulic oils or general purpose lubricating oils.
ADVANTAGES
Minimal Viscosity Change at Operating Temperatures
Rust and Oxidation Protection
Low Carbon Forming
Compatible with Sealants and Painted Surfaces
High Film Strength
Reduces Friction and Wear
Extends Equipment Life
TYPICAL SPECIFICATIONS
TEST ASTM METHOD RESULTS
SAE viscosity grade 10 wt 20 wt 30 wt
ISO viscosity grade ------ 32 68 100
Pour Point, oF D-97 -33 -25 -21
Flash Point, oF D-92 432 475 502
Viscosity, sus @ 100 oF D-445 170 350 500
Viscosity, sus @ 210 oF D-445 46 57 65
Viscosity Index --- 102 100 100
Foam Test D-892 Pass Pass Pass
Rust Test D-665 Pass Pass Pass
The name of this product or group of product is for product identification only. HUSK-ITT CORPORATION makes no warranties, representation or conditions of any kind expressed implied, whether for merchantability of fitness with respect to these products.
AMTEC HLO-AW SERIES SYNTHETIC OIL are produced from highly refined lubricating base stocks and hydraulic oil additive packages. These products are designer to meet exceed the demanding performance requirements of Cicinnati Milacron, Hagglunds-Denision, and Vickers. With an additive system that is compatible with all relevant metals, AMTEC HLO-AW SERIES SYNTHETIC OIL are universal-type products that can be recommended for use in almost all types of hydraulic system applications. It had been used in hydraulic system containing any combination of pumps operating at high outputs.
The low zinc additive package provides good oxidation protection, thermal stability, water tolerance and pump durability. The additives found in AMTEC HLO-AW SERIES SYNTHETIC OIL can make stop and prevents hydraulic seal leaks, recondition old dry hydraulic seals also enhance the wear characteristics of the fluid and inhibit foam from forming in the oil. The hydraulic oils offer an excellent level of protection against rust and corrosion in the event of water contamination.
TYPICAL SPECIFICATIONS
PROPERTIES METHOD RESULTS
ISO Viscosity Grade ASTM D-4052 AW32 AW46 AW52 AW68 AW100
Density @ 15oC, kg/I ASTM D-92 0.870 0.875 0.880 0.880 0.890
Flash Point, oC ASTM D-97 218 220 228 228 238
Pour Point, oC ASTM D-445 -18 -15 -15 -15 -12
Kinematic Viscosity, cST
@ 40oC68 30.4 48.1 67 67.2 97
@ 100oC 5.2 6.91 8.0 8.50 10.9
Viscosity Index ASTM D-2270 152 153 153 152 152
Appearance Visual ASTM D-1500 2.0 3.5 3.5 4.0 4.0
Benefit
- Prevents wear
- Protects against rust and corrosion
- Resists foaming
- Low sludge-forming tendencies
- Economical
- Excellent high-speed/high-pressure pump performance
- Water tolerance
- Stops and prevents hydraulic seal leaks
Approvals
Are universal performance fluids that will meet the requirements of:
- Hanglunds-Denison HF-O, HF-1, HF-2 (mono-and multigrade)
- Vickers M-2950-S (mono-multigrade)
- US Steel 127, 136
- Racing vane Pumps – Variable Volume
- Cincinnati Milacron P-68,P-69 and P-70
The name of this product or group of product is for product identification only. HUSK-ITT CORPORATION makes no warranties, representation or conditions of any kind expressed implied, whether for merchantability of fitness with respect to these products.
AMTEC TURBINE SERIES SYNTHETIC OIL are formulated with highly refined paraffin base stocks and specially selected additives. The oils are designed for premium turbine oil performance, particularly in the areas of resistance to oxidation and to the formation of sludge & varnish at elevated temperatures. The additive components in AMTEC TURBINE SERIES SYNTHETIC OIL also afford exceptional rust and corrosion protection.
AMTEC TURBINE SERIES SYNTHETIC OIL offer outstanding thermal stability, extended service life and strong water separation properties. The anti-oxidation properties plus the other features render them an outstanding choice for turbine use. AMTEC TURBINE SERIES SYNTHETIC OIL are also used in reciprocating compressors, hydraulic systems where anti-wear additives are unacceptable, gear reducers requiring superior rust and oxidation inhibited lubricants, high temperature circulating oil systems, machine tools and electric motor and pump ring oil bearings.
TYPICAL SPECIFICATIONS
PROPERTIES METHOD RESULTS
ISO Viscosity Grade 32 46 68
Density @ 15˚C, kg/I ASTM D-4052 0.870 0.879 0.882
Flash Point, ˚C ASTM D-92 308 314 320
Pour Point, ˚C ASTM D-97 -18 -15 -12
Kinematic Viscosity, cST ASTM D-445
@ 40 ˚C 31.5 46.2 68.0
@ 100 ˚C 5.30 6.75 8.65
Viscosity Index ASTM D-2270 101 101 99
Benefit
● Outstanding thermal stability
● Exceptional protection against rust and corrosion
● Extensive service life capacity
● Low Carbon Forming
● Unsurpassed water separation properties
● Reduces friction and wear
● Extends equipment and lubricants life
High Film Strength
Approvals
- Cincinnati Milacron P-38, P-55 and P-57
- General Electric GEK-32568
- Solar Turbines ES9-224
-U.S. Military MIL-H-176720
- DIN 51524, Part 1
- Hagglunds-Denison HF-1
- Hagglunds-Denison HF-0 Bench Test
The name of this product or group of product is for product identification only. HUSK-ITT CORPORATION makes no warranties, representation or conditions of any kind expressed implied, whether for merchantability of fitness with respect to these products.
AMTEC HI-TEMP GREASE represents some of the latest in lubrication technology. It is formulated from the highest quality petroleum base stocks coupled with newest additive available to help produce the high temperature characteristics usually associated with expensive synthetic based greases. This unique blend, together with its shear stable thickening system, provides the maximum protection against friction, wear and corrosion.
AMTEC HI-TEMP GREASE is not just another “non-melt” grease and does not contain any moly graphite or clay fillers.
USAGE
AMTEC HI-TEMP GREASE was designed primarily for severe high-temperature service but has unsurpassed performance in normal grease applications. Due to its high film strength, anti-wear properties and wide temperature range (-5oF to 750oF), it may be used in a wide variety of applications which include bearings and slides in ovens, kiln cars, mills pumps, roll, forklifts, etc.
ADVANTAGES
High Film Strength
Wide Temperature Range
Extreme Pressure Resistance
Non-melting
Water-resistant
Reduce friction and wear
TYPICAL SPECIFICATIONS
Basic Thickener Synthetic Base Oil Viscosity
N.L.G.I. No 2 SUS @ 100oF 4400
Worked Penetration 265-295 SUS @ 210oF 188
Color Light Brown Flash Point, oF 750
Dropping Point, oF None Pour Point, oF -5
Timken OK Load, lbs 50 Rust Test 9A.S.T.M. D-1743 Pass
The name of this product or group of product is for product identification only. HUSK-ITT CORPORATION makes no warranties, representation or conditions of any kind expressed implied, whether for merchantability of fitness with respect to these products.
AMTEC SYNTHETIC RED GREASE is a unique high temperature, extreme pressure, non-melting premium quality grease designed for every heavy duty service adverse environments. It is a blend of high – quality petroleum oil and special synthetic polymers which work together to form an extremely water-resistant, tough lubricating film that prevents water washout and metal to metal contact even under extreme pressure or shock loading.
AMTEC SYNTHETIC RED GREASE is formulated with the optimum amounts of additives to provide maximum protections against rust, corrosion, and oxidation.
AMTEC SYNTHETIC RED GREASE contains no fillers or clay thickeners. This distinctive red color makes is easy to identify during and after lubrication.
AMTEC SYNTHETIC RED GREASE with its unique qualities can be used in a wide variety of applications, thus reducing the number of lubricants you must keep on hand. Some such applications include ball and roller bearings, bushings, slides, valve operators and bearings, gears, screw drives, couplings, cranes and general lubrication, especially where loads may be quite heavy and speeds slow.
ADVANTAGES
Withstands Extreme Pressures
Wide Temperature Range (0oF to 700 oF)
Extremely Resistant to water washout
Excellent Metal Adherence
Will Not Melt or Run Out
Prevent Rust and Corrosion
Reduces Wear
TYPICAL SPECIFICATIONS
Basic Thickener Synthetic Flash Point, oF 700
N.L.G.I. No 2 Pour Point, oF 0
Worked Penetration 275 Dropping Poin, oF None
Base Oil Viscosity Color Red
SUS @ 100oF 4100 Timken OK Load 60
SUS @ 210oF 280 Rust Test (A.S.T.M.D-1743) Pass
The name of this product or group of product is for product identification only. HUSK-ITT CORPORATION makes no warranties, representation or conditions of any kind expressed implied, whether for merchantability of fitness with respect to these products.
AMTEC ALTEC SYNTHETIC GREASE is are a high performance, low temperature grease designed for high speeds and moderate loads. AMTEC ALTEC SYNTHETIC GREASE is blended from the highest quality petroleum base stocks and selectively treated with rust, oxidation and anti – wear additives coupled with an extremely shear stable thickener system.
AMTEC ALTEC SYNTHETIC GREASE was designed to provide excellent lubrication, wet or dry, over a wide temperature range (-65oF to 500 oF) in a large variety of industries, including textile, food processing, agriculture, automotive, etc, AMTEC ALTEC SYNTHETIC GREASE is recommended for all bearing surfaces including fan bearings, spindles, freezer bearings, electric tools, slides, conveyors, etc.
ADVANTAGES
Wide temperature range
Excellent for high speeds
Extremely resistant to water
Prevents rust and corrosion
Extreme pressure resistant
Reduces friction and wear
TYPICAL SPECIFICATIONS
TEST ASTM TEST METHOD RESULTS
Color Amber
Thickener Synthetic
N.I.G.I. grade 2
Worked Penetration
60 Strokes D – 217 280
10.000 Strikes D – 217 290
Base Oil Viscosity
SUS @ 100 oF D – 445 100
SUS @ 210 oF D – 445 39
Pour Point, oF D – 97 -65
Flash Point, oF D – 92 500
Dropping Poin, oF D – 566 500
Oxidation Stability
(100 hrs. @ 210 oF) psi Loss D – 942 5
Oil Separation, % Loss D – 1742 5
Rust Test D – 1743 Pass
Timken OK Load, lbs D – 2509 40
The name of this product or group of product is for product identification only. HUSK-ITT CORPORATION makes no warranties, representation or conditions of any kind expressed implied, whether for merchantability of fitness with respect to these products.
AMTEC LITHIUM COMPLEX MP GREASE are high temperature lubricants formulated with a lithium complex thickener and premium quality petroleum base oils to provide high temperature stability and excellent water wash-off property. The special thickener gives rice to an outstanding work-shear stability: resisting both softening and hardening of the grease during use. These greases have high dropping point, which resist meting and leakage form bearings operating at elevated temperatures System wear is reduced through the use of AMTEC LITHIUM COMPLEX MP GREASE due to the presence of effective extreme pressure and anti-wear agents. They are also fortified with rust and corrosion inhibitors for optimum protections. AMTEC LITHIUM COMPLEX MP GREASE are truly multi-purpose lubricants, which can replace two, there or possibly four other greases. Thos reduces inventory and minimizes the chance of misapplication with the wrong grease.
TYPICAL SPECIFICATION
PROPERTIES METHOD RESULTS
NLGI Type #1 #2 #3
Thickener Type ----- Lithium Complex-----
Colour Yellow Yellow Yellow
Texture Smooth Smooth Smooth
Dropping Point, oC (min). 400 400 400
Worked penetration
@ 25 oC 1/10 mm 325 280 235
Penetration 10.000 stroke
% change 2.49 7.19 8.64
Timken OK Load, lbs (min) 45 45 45
Four Ball EP Test
Wel load, kg 250 250 250
Water Washout @ 38 oC, % Lose n/a 0.057 0.03
Wheel bearing Leakage, g 1.94 0.03 0.03
Oil Spraration @ 100oC, % wt 0.98 0.50 0.46
Viscosity @ 100oC, cST ------------- 17 – 21 -------------
Benefit
- Outstanding high temperature wheel bearing performance
- Protect against the heat generated by the heavy brake loads of vehicle pulling trailers
- Excellent extreme pressure and anti wear performance
- Resists weall bearing leakage at high temperatures
- May be used continuously a temperature of up to 190 oC
- Highly water resistant
Application
AMTEC LITHIUM COMPLEX MP GREASE are recommended for industrial applications where a high temperature, extreme pressure , water resistant grease is required. Typical applications include for bearings, couplings, and gears in extended use and heavy duty services. In addition to industrial applications. This includes lubrication of cars, buses, vans, trucks and farm equipment wheel bearings, even under heavy and shock loading. Ball joints, chassis and U-joints could also be well served by this product.
The name of this product or group of product is for product identification only. HUSK-ITT CORPORATION makes no warranties, representation or conditions of any kind expressed implied, whether for merchantability of fitness with respect to these products.
AMTEC COOLTEC GREASE 2 is a premium quality, all purpose, high temperature grease. It is a blend of the highest quality base oils and thickeners available. Treated with the most modern additives, they provide lasting protection against rust, corrosion and oxidation.
The most important built-in feature in AMTEC COOLTEC GREASE 2 is the tenacious quality of its polymer additives. Such a feature helps produce more uniform friction drag, cushion shock and minimize wear.
AMTEC COOLTEC GREASE 2 with its “cling to” ability will stay on the metal surface much longer than most conventional greases on the market today, resulting in longer – lasting lubricity, which fewer lubrication intervals.
AMTEC COOLTEC GREASE 2 may utilized for application where a multipurpose No. 2 grade grease is employed, it was designed to fit a wide variety of automotive, industrial, agricultural and household applications such as :
Wheel bearings
Ball joints
Universal joints
Electric motors
Fans & blowers Heavy – duty truck
Guide rail and sliding surface
Garden tractors
Fith wheels
Conveyors
ADVANTAGES:
High Temperature
Low coefficient of friction
Wider temperature range Labor saving
Reduced wear
Extremely water resistance
TYPICAL SPECIFICATIONS
Base Thickener Synthetic
N.L.G.I. No 2
Worked penetration 265-295
Dropping Point oF Over 500
Oil Viscosity @ 210 oF SUS 70
Flash Point oF 510
Pour Point oF 0
Color Amber
Texture Buttery and Tenacious
The name of this product or group of product is for product identification only. HUSK-ITT CORPORATION makes no warranties, representation or conditions of any kind expressed implied, whether for merchantability of fitness with respect to these products.
AMTEC X-TRA HEAVY DUTY GREASE is an extra heavy duty, high temperature, multi purpose, lithium complex grease fortified with synthetic polymers, anti-wear agents and the most advanced rust oxidation preventatives available. It is designed to “stay put” under the most severe operating condition, resulting in longer lasting lubricity, with fewer lubrication intervals.
AMTEC X-TRA HEAVY DUTY GREASE is extremely water resistant and has natural affinity for metallic surfaces, as it forms a tough durable film against water washout, dirt and prevents metal-to-metal contact, even under extreme conditions of shock loading. The distinctive brown color makes it easy to identify during and after application.
USAGE
AMTEC X-TRA HEAVY DUTY GREASE may be utilized for applications where a multi-purpose grade grease is employed, but was especially designed for severe service applications in the presence of water, dirt, mud, or excessive wear and extreme loads. Formulated to “stay put”, it will not melt or run out of bearings surfaces due to its excellent cohesive and adhesive properties. Some typical applications include all wheel bearings, including disc brake applications, fifth wheels, ball joints, conveyors, universal joints, pilot bearing, chassis lubrications, cams and slides, etc. found in marine, industrial, automotive and mining applications.
ADVANTAGES:
Excellent Metal adherence
70 lb. Timken OK Load
wide temperature range
NLGI rate GC-LB Prevents Rust And Corrosion
Dramatically Reduces Wear
Protects Against Water Washout
TYPICAL SPECIFICATIONS
Base Tickener
NLGI No
Worked Penetration
Dropping Point oF
Oil Viscosity
@ 210 oF SUS
Flash Point oF
Pour Point oF
Color
Texture Semi Synthetic
2
265-295
None
90
450
0
Amber
Buttery/
Tenicious
The name of this product or group of product is for product identification only. HUSK-ITT CORPORATION makes no warranties, representation or conditions of any kind expressed implied, whether for merchantability of fitness with respect to these products.
AMTEC SUPER HEAVY DUTY GREASE is heavy duty tenacious, synthetic thickeners available to provide a truly multi services, friction reducing non melting grease with protection in normal and severe service application
AMTEC SUPER HEAVY DUTY GREASE is a blend of the highest quality base oils and polymers coupled with proprietary extreme pressure additive which form a tough durable film of protection from friction, wear and corrosion over a wider temperature range ( -200F to 7000F )
AMTEC SUPER HEAVY DUTY GREASE is unique formulation provides superior adhesion to metal surfaces that does nor easily wash off, run out or separate even under adverse conditions of water, thus providing lower grease consumption and extend lubrication cycles.
USAGE
AMTEC SUPER HEAVY DUTY GREASE provide performance in a wide variety of conventional and severe service applications found in a diverse range of industrial mining constructions, agricultural applications.
AMTEC SUPER HEAVY DUTY GREASE is recommended for all roller, bushing, couplings universal joints, and sliding services where a multi purpose or extreme pressure grease is required.
ADVANTAGE
• Withstands extreme pressure
• Wide temperature range
• Excellent metal adherence
• Prevents rust & corrosion
• Highly water resistant
• Reduces grease inventories
• Reduces Friction & wear
• Will not melt or run out
TYPICAL SPECIFICATIONS
TEST METHOD RESULT
Base Tickener Synthetic
N.L.G.I Grade - 2
Worked penetration D-217
60 strokes 285
10.000 strokes 300
Base oil viscosity D-445
SUS@1000F 1200
SUS@2100F 90
Pour Point 0F D-97 -20
Flash Point 0F D-566 410
Dropping Point,oF D-566 None
Corrosion Preventative Test D-1743 Pass
Timken OK load, Lbs D-2509 70
Color Amber
The name of this product or group of product is for product identification only. HUSK-ITT CORPORATION makes no warranties, representation or conditions of any kind expressed implied, whether for merchantability of fitness with respect to these products.
AMTEC OPEN GEAR GREASE is a heavy duty tenacious, semi – synthetic open gear lubricant containing a balanced blend of molybdenum disulfide (moly) and graphite, incorporated in a non – asphaltic, no – melt base grease that contains no cly fillers.
Treated with the most modern additives to provide lasting protection against extreme pressure, wear, rust, and oxidation on gear faces and sliding surfaces.
USAGE
Typical application of AMTEC OPEN GEAR GREASE include all open gears, sliding surfaces, gibs, guides and ways of forging hammers, klin car wheels, and is an excellent cable dressing.
ADVANTAGES
PLATING ACTION is established between metal surfaces by the lubricating solid that develop a smoother surface. Working life of both the parts and the greases are substantially increases.
CONTACT LUBRICATION with the lubricating solids prevents grease film failure due to unexpected loads, start-up or other conditions witch may exceed the load capabilities of the bulk film lubrication. Contact lubrication protects the working surface from excessive wear caused by cold welding.
REDUCED WEAR and increased parts life are the result of the protection provided by the lubricating solids.
COST REDUCTION is accomplished by increased part life, less downtime and extended lubrication cycles.
FRICTION IS LOWERED, reducing contact area temperature, resulting in increase working of the grease.
TYPICAL SPECIFICATIONS
N.L.G.I.No 00*/ 0 Timken OK Load, lbs 60*/65
Oil Viscosity, SUS @ 210 oF 120*/120 Rust test Pass
Flash Point, oF 400*/ 424 Base Type Synthetic
Dropping Point, oF None Color Amber*/Black
Worked Penetration 400-430*/275 Lubricating Solids Graphite
Molybdenum Disulfide
The name of this product or group of product is for product identification only. HUSK-ITT CORPORATION makes no warranties, representation or conditions of any kind expressed implied, whether for merchantability of fitness with respect to these products.
AMTEC OPEN GEAR 273, “SPRAYABLE” Is a balanced blend of sub micron size lubricating solids in a semi synthetic, non-asphaltic, no-melt base grease that provides protection against extreme pressure, wear, rust and corrosion on gear faces and sliding surfaces. AMTEC OPEN GEAR 273, “SPRAYABLE” is blended with a unique quick drying, non-flammable solvent that it not hazardous to the environment or to the ozone. This solvent produces a product that is easily applied by spraying, brushing or dipping, then the solvent quickly evaporates leaving a tenacious Open Gear Grease in place that will not migrate or sling off.
AMTEC OPEN GEAR 273, “SPRAYABLE” is designed to provide protection to open gears, chains, sliding surfaces, gibs, guides and ways operating in unusually wet or hot application. The spray able characteristics of AMTEC OPEN GEAR 273, “SPRAYABLE” makes it an excellent chain lubricants and wire line dressing that penetrates to the core of the wire line or chains pints, to provide maximum wear protection from twisting, bending and stretching.
AMTEC OPEN GEAR 273, “SPRAYABLE” is easily applied to either open, gears, wire rope or chains. The carrier solvent quickly evaporates, leaving a durable grease coating produces an “armor like” plating that protects the metal surfaces from shock loading, galling, pitting, corrosion, wiping or other extreme conditions.
TYPICAL SPECIFICATIONS
TEST ASTM RESULTS
METHOD
Color ---- Black
Appearance ---- Liquid
Base fluid ---- Semi-synthetic
Base Oil Viscosity, SUS @ 100 oF D - 445 5000
Flash Point, oF (with solvent) D – 92 None
Flash Point, oF (without solvent) D – 92 450
Drop Point, oF (without solvent) D – 566 500
Timken Ok Load, Lbs D – 2509 60
Rust Test D – 665 Pass
Lubricating Solids Molybdenum disulfide,
Graphite
The name of this product or group of product is for product identification only. HUSK-ITT CORPORATION makes no warranties, representation or conditions of any kind expressed implied, whether for merchantability of fitness with respect to these products.
AMTEC POLYUREA SHEAR STABILITY is second generation Polyurea grease a shear stable product with exceptional and extreme pressure characteristics and excellent water resistance, it is provide extended superior performance and represents the highest level of technical excellence in the field of lubrication developed for commercial application.
AMTEC POLYUREA SHEAR STABILITY is a blend of the highest quality base oils and polymers with AMTEC ‘S newest proprietary extreme pressure additive which forms a tough durable film of protection from friction, wear and corrosion over a wider temperature 275 oC (530oF).
AMTEC POLYUREA SHEAR STABILITY unique formulation provides superior adhesion to metal surfaces that does not easily wash off, run out or separate even under adverse conditions of water, steam or dilute chemicals thus providing lower grease consumption and extended lubrication cycles.
USAGE
AMTEC POLYUREA SHEAR STABILITY is recommended for steel mills, off road equipment, fleet and commercial applications and severe service applications found in diverse range of industrial, paper and steel mills, conveyers, marine, mining, construction, agricultural, and automotive application.
TYPICAL SPECIFICATIONS
TEST ASTM TEST METHOD RESULTS
Thicker Polyurea
Texture Smooth
Color Green
Penetration Worked D-2665 285
Dropping Point oF (oC) Min D-1831 500 (20)
Water Washout % Loss Max D-1264 10.0
Rust Prevention D-1743 Pass
Copper Corrosion, Rating D-4048 1 b
Oxidation Stability, PSI Loss max D-942 5
Oil Separation % Loss, max D-1742 5.0
- Ball
Weld Point D-2596 400
Load Wear Index, Kgf D-2596 50
Timken OK Load, lbs D-2509 60
Base Oil Characteristics
Viscosity @ 100oC, cST D-445 14.5
@ 40oC, cST D-445 145
@ 210oF, SUS D-445 65.0
@ 100oF, SUS D-445 70
The name of this product or group of product is for product identification only. HUSK-ITT CORPORATION makes no warranties, representation or conditions of any kind expressed implied, whether for merchantability of fitness with respect to these products.
LUBRICATING PASTE AND ANTI-SEIZE COMPOUND FOR HIGH TEMPERATURE
AMTEC 2000 ANTI – SEIZE GREASE is heavy – duty industrial anti-seize and lubricating paste containing very finely divided metallic particle in special no-melt semi-synthetic carrier. AMTEC 2000 ANTI –SEIZE GREASE leaves a protective film that seals and protects metal parts even under the most extreme conditions of heat, pressure, steam and saltwater exposure.
USAGE
AMTEC 2000 ANTI – SEIZE GREASE was designed as a preventative maintenance tool providing complete parts protection on threaded fitting and all metal surfaces subjected to harsh environments or high temperatures to + 2000oF. AMTEC 2000 ANTI – SEIZE GREASE was formulated to fit a wide variety of marine, metal working, automotive, oilfield, construction and farm equipment applications. A few such examples include
THREADED FIRINGS
RIG DRIVES
SPROCKETS & CHAINS
CASTING EQUIPMENT
SPLINES
LOW SPEED WORM GEARS MANIFOLD STUDS & BOLTS
WINCHES
BRAKE CAMS & PINS
CONVEYORS
VALVE SHAFTS
SENSORS
ADVANTAGES
AMTEC 2000 ANTI – SEIZE GREASE is not just another anti-seize/thread lubricant. Unlike conventional products on the market, the maximum blend of metallic solids has been homogenized into a specially designed semi-synthetic lubricating grease which does not contain clay or soap base thickeners. This helps to provide a superior product that will nor melt and run out after application. It also helps to reduce friction of metal surfaces and allows easy movement of threaded connections during assembly and disassembly which makes for tighter make-ups and leak free joint. Other advantages include:
PROTECT TO + 2000 OF
REDUCES TORQUE
PREVENTS CARBON FUSION
PREVENTS RUST & CORROSION
EXCELLENT LUBRICITY PREVENTS GALLING & SEIZING
STEAM & WATER PROOF
CHEMICAL RESISTANT
EXTREME PRESSURE LUBRICANT
NON-MELTING
MEETING MIL SPEC. MIL – A – 907 E
The name of this product or group of product is for product identification only. HUSK-ITT CORPORATION makes no warranties, representation or conditions of any kind expressed implied, whether for merchantability of fitness with respect to these products.
AMTEC CHAIN & CABLE LUBE is a transparent, heavy-duty dry film lubricant that cleans, penetrates and lubricates. It is formulated with the latest synthetic additives to assure maximum penetration and protection against rust and corrosion. When applied, the carrier solvent quickly evaporates, leaving behind a wax-like extreme pressure lubricant which will not wash-off or attract dust.
USAGE
AMTEC CHAIN & CABLE LUBE was formulated to lubricate, preserve and protect not only chains and cables but as an excellent extreme pressure lubricant for all bearings and sliding surfaces. It is designed to fit a wide variety of industrial, agricultural, marine, automotive and household applications, such as:
● CHAIN AND CABLES ● SLIDING DOORS AND WINDOWS
● CONVEYOR BEARINGS ● BUSHINGS AND SHAFTS
● NUTS AND BOLTS ● DRAGLINES
● CUTTING BLADES ● LOCKS AND HINGES
● CHAIN SAWS ● GUNS
ADVANTAGES
● NON-STAINING ● WATERPROOF
● DISPLACES MOISTURE ● CHEMICAL RESISTANT
● CLEANS & LUBRICATES ● PREVENTS RUST & CORROSION
● REDUCES WEAR ● WILL NOT ATTRACT DIRT
TYPICAL SPECIFICATIONS
TEST ASTM RESULTS
METHOD
Base Carrier --------- Petroleum Solvent
Color Light Amber
Visual Low Viscosity Liquid
Flash Point, 0F D-92 145
Coefficient of Friction LFW -4
Dynamic 0.077
Static 0.087
Falex Pin & Vee Block
ft. lb., Pass D-3233 (B) 1000
Salt Spray Corrosion
(5% @ 100 hrs.) B-117 No Rust
Humidity Cabinet Test
(60 hrs @ 120 0F) D-1748 Pass
The name of this product or group of product is for product identification only. HUSK-ITT CORPORATION makes no warranties, representation or conditions of any kind expressed implied, whether for merchantability of fitness with respect to these products.
AMTEC COOLUBE GREASE is a premium quality, multi-purpose, non-soap grease. It gives better lubrication in more applications, wet or dry, over a wider temperature range (-400F to 2500F), and for longer periods of time than ordinary soap-base greases.
AMTEC COOLUBE GREASE is a truly multi-purpose grease. Because of its excellent stability and its E.P. characteristics, it will remain on all metal and bearing surfaces longer than most ordinary greases. Formulated not to melt or run out of bearings even at higher temperatures.
USAGE
AMTEC COOLUBE GREASE is specifically formulated for use on anti-friction bearings, journals and all general greasing; where a single multi-purpose lubricant is desired for economy, simplification of inventory and general greasing of equipment. Some typical applications include fans, blowers, pumps, conveyor bearings, ball bearings, journal bearings, roller bearings, universal joints and all other lubrication points having sliding or rolling friction which require a multi-purpose grease.
ADVANTAGES
● Wide Temperature Range ● Reduced Wear
● Extremely Water Resistant ● Non-Melting
● Low Coefficient of Friction ● Prevents Rust and Corrosion
TYPICAL SPECIFICATIONS
TEST ASTM METHOD RESULT
N.L.G.I. Grade ---- 2
Color Green
Base Thickener Calcium Complex
Worked Penetration D-217 265-295
Base Oil Viscosity, D-445
SUS @ 100°F 250
SUS @ 210°F 50
Pour Point, °F D-97 -40
Flash Point, °F D-92 250
Dropping Point, °F D-566 NONE
Corrosion Preventative Test D-1743 PASS
Timken OK Load, lbs. D-2509 40
The name of this product or group of product is for product identification only. HUSK-ITT CORPORATION makes no warranties, representation or conditions of any kind expressed implied, whether for merchantability of fitness with respect to these products.
AMTEC SUPER METAL CONDITIONER is a specially formulated premium crankcase oil conditioner. It is designed do quiet valve and lifter noise, reduce oil consumption and increase horsepower by enhancing the viscosity and protection of the motor oil at both normal and extended high temperature operation.
AMTEC SUPER METAL CONDITIONER utilizes special proprietary additives that chemically plate the metal surface against wear and scuffing thus lowering maintenance costs and increasing the life of the engine.
AMTEC SUPER METAL CONDITIONER contains active anti-oxidation ingredients that increase the oxidation properties of the motor oil and help to neutralize the corrosive combustion formed acids that damage the engine AMTEC SUPER METAL CONDITIONER does not contain any chlorinated paraffin that can increase combustion acid formation.
AMTEC SUPER METAL CONDITIONER, when added to the crankcase oil, improves the ring and valve stem seals which restores compression’s reduce oil consumption and exhaust smoke and increases fuel economy. AMTEC SUPER METAL CONDITIONER is recommended for use with gasoline and diesel engine motor oils in both older and new cars, trucks, tractors and vans.
Directions : pour 2% - 5% of AMTEC SUPER METAL CONDITIONER into the crankcase at each oil change.
ADVANTAGES :
Helps quiet noisy engines
Reduces oil consumption
Lengthens engine life
Reduces exhaust smoke Reduces friction and wear
Increases horsepower
Lowers maintenance costs
Increases fuel economy
TYPICAL SPECIFICATIONS
Color Red
Viscosity
Cst @ 40oC 140
Cst @ 100oC 14.0
Specific Graffiti
Flash Point oF (oC) 52 (274)
Pour Point oF (oC) 5 (-15 )_
The name of this product or group of product is for product identification only. HUSK-ITT CORPORATION makes no warranties, representation or conditions of any kind expressed implied, whether for merchantability of fitness with respect to these products.
AMTEC GEARTEC TREATMENT is an industrial and automotive oil concentrate, treatment that represents the latest in lubricant additive technology. It is formulated to dramatically reduce friction and wear, quiet and bearing noises, and reduce surface temperatures, thus permitting the gear assemblies to run more efficiently.
AMTEC GEARTEC TREATMENT forms a “armor like” chemical plating on the metal parts that reduces friction, increases the load carrying capacity, minimize wear and prevents galling, scuffing, or scoring on loaded surfaces.
AMTEC GEARTEC TREATMENT is environmentally friendly as it does not contain any chlorinated paraffin, graphite, moly, or PTFE (Teflon)
AMTEC GEARTEC TREATMENT is a heavy-duty oil treatment designed to smooth the shifting and protect against friction and heat in all makes and models of manual transmission, differentials and transaxles. Because
AMTEC GEARTEC TREATMENT contains a proprietary metal conditioner it is excellent as a engine assembly lubricant for all gasoline and diesel engines. It’s tacky lubricants film a protective coating during assembly of bearings, gears, camshafts, mechanical and hydraulic lifters and other parts with close tolerances. This thin Adhesive film protects engine parts from “dry starts” during the critical wear – in period.
DIRECTIONS : mix as little as 5% by volume of AMTEC GEARTEC TREATMENT to a standard gear oil at each oil change.
ADVANTAGES :
Quiet gear and bearings noises
Reduces friction and wear
Reduces gear temperature Improves bearings and gear life
Prevents corrosion
Increases output efficiency
TYPICAL SPECIFICATIONS
Appearance Tacky Oil
Color Amber
Viscosity, cst @ 100oC 48
Flash Point oF (oC) 52 (273,9)
Pour Point oF (oC) 12 (-11)
Specific Gravity 0.88
The name of this product or group of product is for product identification only. HUSK-ITT CORPORATION makes no warranties, representation or conditions of any kind expressed implied, whether for merchantability of fitness with respect to these products.
AMTEC HEAVY DUTY TRANSMISSION CONCENTRATE is superior multi – purpose gear metal treatment and oil conditioner. It form an anti friction, extreme pressure, chemical film on the gear metal surface. It is scientifically formulated for use in bearings, gears, manual transmission and differentials. It enhances and extends the useful life of transmission lubricants.
AMTEC HEAVY DUTY TRANSMISSION CONCENTRATE is composed of premium quality base oils and specially selected chemicals. It is designed to improve, enhance and lengthen peak transmission performance.
DIRECTIONS FOR USE :
AMTEC HEAVY DUTY TRANSMISSION CONCENTRATE is designed for truck, automotive, industrial and farm transmission, differentials and bearings. It is used in manual transmission.
AMTEC HEAVY DUTY TRANSMISSION CONCENTRATE provides the following extra features and benefits to transmission oils :
• Treats the metal by forming a very tough, slick chemical boundary film on the surface of the metal. This tenacious extreme pressure film reduces friction, minimize wear and prevents galling, scoring and seizure.
• Increase the load carrying capabilities of the moving gears.
• Increase the efficiency and operating life of the transmission oils.
• Reduces friction and saves energy and power
• Lower maintenance cost.
• Quiets the noise of gear and bearing operation : smooths the operation of stick, shift, prolongs differential life, and eases manual steering
• Smooth pitted bearing and gears
• Saves money and time.
DIRECTIONS :
For DIFFERENTIALS and TRANSMISSION GEARS, use 2-5 % by volume AMTEC HEAVY DUTY TRANSMISSION CONCENTRATE
The name of this product or group of product is for product identification only. HUSK-ITT CORPORATION makes no warranties, representation or conditions of any kind expressed implied, whether for merchantability of fitness with respect to these products.
AMTEC DIESEL FUEL SUPPLEMENT is especially formulated to solve all diesel related problems in high sulfur diesel fuels. With today’s poor quality fuels, breakdown, filter clogging, injector malfunctions, intolerable emissions, sludge, moisture, gum varnish, algae, and poor fuel economy are common problems.
AMTEC DIESEL FUEL SUPPLEMENT is a concentrated performance improver formulated for the diesel engine which reduce your maintenance cost and help engine maximum year around performance.
AMTEC DIESEL FUEL SUPPLEMENT is a blend of the highest quality most recent, scientifically selected and tested components. It is truly multi functional blend provides the following out standing features and benefits :
• Improve the combustion diesel engine and dramatically reduce smoke emission.
• Cleans up dirty injectors and keep the injector tips free of deposits in the proper spray pattern in the combustion are possible.
• Saves fuel and produces more power – fuel savings exceed cost of additive.
• Provides corrosion protection of the tanks, lines, pumps, and the injectors.
Provide fuel storage stability and protects against gum, varnish and sludge build up.
• Protects against conditions that promote bacteria, algae and microbial growth.
• Increase fuel filter life and keeps fuel system running at peak performance.
• Improves drive ability, decrease rough idling, noise and engine knock.
• Meets lubricity requirements for all diesel fuel injection system and reduces pump and injector wear.
• Contains cetane improver for smoother engine operation.
• Passes and exceeds the Cummins diesel fuel engine test.
TREATMENT RATE : Mix of I gallon diesel Fuel Supplement with 3000 gallons of diesel fuel
The name of this product or group of product is for product identification only. HUSK-ITT CORPORATION makes no warranties, r
epresentation or conditions of any kind expressed implied, whether for merchantability of fitness with respect to these products.
AMTEC HEAT TRANSFER OIL is a premium quality, Highly refined, medium viscosity – index, naphtenic mineral oil suited for use as heat transfer fluid in indirect closed head transfer system. Indirect closed fluid heat transfer system operating at bulk oil temperatures up to 420 o C
Typical properties
PROPERTIES METHOD RESULT
Density @ 15 o C, kg /I ASTM D-4052 0.905
Flash Point PMcc, oC ASTM D-93 320
Pour Point COC, o C ASTM D-92 230
ISO 2592
Neutralization value, mg KOH/g ASTM D-974 0.05
Kinematic Viscosity, cST ASTM D-445
@ 40 o C 24,01
@ 100 o C 5,5
Viscosity Index ASTM D-2270 33
Pour point, o C ASTM D-97 - 30
Initial Boiling Point, o C ASTM D – 86 > 360
Coefficient Of Thermal Ezpansion per, o C 0.00063
Benefit
• High heat transfer coefficients
• High oxidation and thermal stability
• Good viscosity temperatures characteristic
• Low vapor pressure
• Non – corrosive
• Non – toxic
